DSM501A PINOUT.

DSM501A -

PINOUT I/O DESCRIPTION. Pin number: Pin name: Description #1: Control: Vout 1 control #2: Vout 2: Vout 2 output factory calibrated PWM output for density of particles over 1 m. #3: Vcc: Positive power supply DC 5V #4: Vout 1: Vout 1 output (PWM) #5: GND: Ground: control pin 1. resistor between pin 1 and ground (square pin on board) to control vout 1 output (pin 4) Resistor value: Description ...

Get Price

Chat With WhatsApp

DSM501A Dust/Air Particulate Sensor – CreateLabz Store

It can simple use for arduino The DSM501A consists of: Light Emitting Diode(LED) Lamp Detector Signal amplifier circuit Output drive circuit 1 Output drive circuit 2 Heater Features PWM output Compact size and lightweight Easy installation 5v Single power supply Application Air cleaner or Air purifier Air condition Air quality monitor Ventilator etc. Pinout of the connector: Pin Description 1 ...

Get Price

Chat With WhatsApp

How to Interface With Optical Dust Sensor : 9 Steps (with ...

Description: Sharp's GP2Y1010AU0F is an optical air quality sensor, or may also known as optical dust sensor, is designed to sense dust particles. An infrared emitting diode and a phototransistor are diagonally arranged into this device, to allow it to detect the reflected light of dust in air. It is especially effective in detecting very fine ...

Get Price

Chat With WhatsApp

DSM501A dust sensor - HackSpark

The dust sensor module DSM501A is low cost,compact size for a particle density sensor. Quantitative particle measurement with the principle of particle counter. FIne particle of which diameters are bigger than one micron could be detected with high sensitivity. Inside heater realizes the self-air taking. One control contact and two output contacts.

Get Price

Chat With WhatsApp

Air quality monitoring IOT – Arduino & sensors connected ...

DSM501A dust sensor. A cheap, photo voltaic dust sensor, seems to be working quite well. It has a heater and an infrared emitter, the beam is facing against the sensor. The heat circulates the air within its sensor area and the reflection created by the dust, hitting the sensor is output as the value – the higher the dust, the higher the amount of light reflection and reading will be. I ...

Get Price

Chat With WhatsApp

DSM501A Dust Sensor 5V Air Measurement For Arduino ...

DSM501A Dust Sensor 5V Air Measurement For Arduino - NB060. 0 Review(s) Rs 580. Reference: NB060. Condition: New product. Can sense tobacco smoke and pollen, house dust and so on; Can measure 1 micron or more of small particles; Small size, lightweight, easy to install ; 5 V input circuit for signal processing; More details. Quanty: Add to cart. Send to a friend *: *: * Share on …

Get Price

Chat With WhatsApp

PINOUT I/O DESCRIPTION

PINOUT I/O DESCRIPTION t=0x9357918 cell=0x9357a78 [0,0] Pin number cell=0x9357ba8 [0,1] Pin name cell=0x9357cd8 [0,2] Description cell=0x9357df8 [1,0] #1 cell=0x9357ed8 [1,1] Control cell=0x9357fb8 [1,2] Vout 1 control cell=0x9358178 [2,0] #2 cell=0x9358258 [2,1] Vout 2 cell=0x9358388 [2,2] Vout 2 output factory calibrated PWM output for density of particles over 1 �m. …

Get Price

Chat With WhatsApp

DSM501A (Dust Sensor Module) – Techonics LTD

The dust sensor module DSM501A is low cost,compact size for a particle density sensor. Quantitative particle measurement with the principle of particle counter. FIne particle of which diameters are bigger than one micron could be detected with high sensitivity. Inside heater realizes the self-air taking. One control contact and two output contacts. The DSM501A consists of: Light Emitting Diode ...

Get Price

Chat With WhatsApp

Optical Dust Sensor - Electronic Components Pinouts ...

2020-12-23· Optical Dust Sensor Pinout . Sharp's GP2Y1014AU0F is a tiny six-pin analog output optical air quality/optical dust sensor that is designed to sense dust particles in the air. It works on the principle of Laser Scattering and is especially effective in detecting very fine particles like cigarette smoke, and is commonly used in air purifier systems. This sensor consists of an infrared emitting ...

Get Price

Chat With WhatsApp

Reverse Engineering: Sharp GP2Y1014AU0F Dust Sensor PM ...

2019-01-06· Sharp GP2Y1014AU0F Pinout: Sharp GP2Y1014AU0F and Arduino connection: In real world it look like this: Arduino Uno connected to the sensor with the 150uF capacitor between the pin 2 and 3 of the sensor and 150ohms resistor from pin 1 on the sensor to the 5V on Arduino. Pin 2 and 4 of the sensors are conected to GND of Arduino Uno and finaly pin 6 on sensor to the 5V pin on Arduino …

Get Price

Chat With WhatsApp

REQUEST FOR APPROVAL

PINOUT I/O DESCRIPTION Pin number Pin name Description #1 Control Vout 1 control #2 Vout 2 Vout 2 output (PWM) #3 Vcc Positive power supply #4 Vout 1 Vout 1 output (PWM) #5 GND Ground 5-3. PIN ARRAY (component view) 5-4. CONNECTOR PART NUMBER Model name Part No. Description Connector’s maker Male 20010WR-05 DSM501A Female 20010HS-05 2mm pitch Yeonho Electrionc …

Get Price

Chat With WhatsApp

Arduino Uno Sharp Dust Sensor Tutorial | Arduino | Maker Pro

2019-08-28· The Arduino code will output the dust concentration level of the sensor in the OLED 128X32. The connections on Sharp's optical dust sensor. Note: For an Arduino Uno, connect pin Vo of the GP2Y1010AU0F to pin A0 of the Uno. Pin V-LED and pin Vcc of GP2Y1010AU0F can be connected to either 5V or of the Uno. The same applies to the Vcc of the ...

Get Price

Chat With WhatsApp

Professional gas sensing solution supplier with over 30-year gas sensor manufacturing experience Contact Us